Virginia Tech® home

Fertilizer Types and Calculating Application Rates

ID

424-035

Authors as Published

Authored by Rory Maguire, Professor and Extension Specialist, School of Plant and Environmental Sciences, Virginia Tech; Mark Alley, W. G. Wysor Professor, School of Plant and Environmental Sciences, Virginia Tech; and Webb Flowers, Extension Agent, Agriculture and Natural Resources/Animal Science, Carroll County (first published August 2019, last reviewed August 2024)

Introduction

Crop production has increased dramatically over the last few decades, much of which has been due to the widespread introduction of chemical fertilizers starting in the mid-1900s. Matching fertilizer application rates to crop needs is an essential component of optimizing crop production. However, different crops in separate fields will require varying rates of the major nutrients nitrogen (N), phosphate (P2O5), and potassium (potash, K2O) due to variations in soil types, soil test phosphorus and potassium levels, and nutrient ranges of different crops. Meeting these N-P2O5-K2O (sometimes abbreviated to N-P-K) requirements without overapplying any of these nutrients is possible by blending various types of fertilizer to give the correct N-P2O5-K2O ratio. This allows you to apply the correct rate of a particular blended fertilizer. Other considerations such as cost of available fertilizers and crop micronutrient requirements also need to be considered when blending fertilizers.

In addition, particle size compatibility is important for uniform spreading of dry, granular fertilizers. Chemical compatibility of liquid fertilizers is important to prevent precipitation or “salting out” of incompatible materials.

This publication covers the use of inorganic fertilizers, sometimes referred to as commercial or chemical fertilizer, to supply the major crop nutrients N, P2O5, and K2O. These nutrients can also be provided from organic sources such as manures, but they are covered in a separate publication, Soil Test Note 5: Fertilizing with Manures, Virginia Cooperative Extension publication 452-705.

Calculating Nutrient Requirements

The first step in applying the correct rate of fertilizer is calculating crop nutrient requirements. A soil test is the only way to measure how much P2O5 and K2O are available in soils, and soil tests are available through several private and public laboratories. An explanation of how to perform soil tests and interpret results is available at www.soiltest.vt.edu.

Applications of P2O5 and K2O may not be required annually, depending on how much is available in particular soils, and the amount of P2O5 and K2O that is required to meet production goals for the specific crop to be grown. As N is much more mobile in soils and must be applied every year to nonlegumes, N requirements are based on the crop to be grown and the soil type that influences yield goals. These recommendations are generally made in conjunction with soil test reports.

Determining the Quantity of N, P2O5, and K2O in a Bag of Fertilizer

The concentrations and the reporting of nutrient concentrations in fertilizers are carefully regulated, with ongoing testing of products to verify proper labeling. An analysis that describes the concentrations of plant-available nutrients can be found on every bag of fertilizer. Also, bulk-blended fertilizers must have a certificate showing the guaranteed analysis of the material.

Generally, there are three numbers that describe, in order, the concentrations of N-P2O5-K2O. For example, a fertilizer bag of diammonium phosphate will have the numbers 18-46-0 on it, which means it contains a minimum of 18 percent N, 46 percent P2O5, and no K2O by weight. For liquid fertilizers, you need to know the density of the solution, as the nutrient concentration is based on the weight and not the volume. Liquid fertilizers such as 30-0-0 (urea ammonium nitrate or UAN), are often used as starter fertilizers or for sidedressing corn. The N-P2O5-K2O numbers do not add up to 100 percent, because fertilizers usually contain filler materials that help granule formation and assist with even product application.

Sometimes the fertilizer label provides additional numbers or additional analysis details if there are secondary or micronutrients such as sulfur, boron, or magnesium in the fertilizer. Table 1 gives the nutrient concentrations in several common fertilizer materials that can be applied directly to crops or used to make blended fertilizers. You may observe slight variations in nutrient concentrations of similar fertilizer products, based on the specific manufacturer.

Blended fertilizers are mixes of these fertilizer materials that are made to vary the N-P2O5-K2O ratio to meet crop requirements. You can find out what blends are available in your area by calling your local fertilizer suppliers and then matching these to your crop requirements.

Common dry, blended fertilizers available include 20-10-10, 20-20-10, 20-20-0, 0-10-40, and many others. Some, such as 10-10-10 and 19-19-19, contain the same ratio of N-P2O5-K2O. It is important to recognize that you would have to apply almost twice as much of the 10-10-10 product to get the same nutrient application as with the 19-19-19 product.

A common liquid fertilizer is urea ammonium nitrate, i.e., 30 percent UAN that weighs 10.86 pounds per gallon and contains 30 percent N by weight.

Table 1. Common basic fertilizer materials used for blending and their nutrient contents
Material Analysis N (%) P2O5 (%) K2O (%)
Ammonium nitrate 33-0-0 33 0 0
Ammonium sulfate* 21-0-0-24S 21 0 0
Diammonium phosphate 18-46-0 18 46 0
Potassium chloride (muriate of potash) 0-0-60 0 0 60
Potassium sulfate** 0-0-50-16S 0 0 50
Potassium magnesium sulfate*** 0-0-22-23S-11Mg 0 0 0
Triple super phosphate 0-46-0 0 46 22
Urea 46-0-0 46 0 0

Note:
*Ammonium sulfate contains 24% sulfur (S)
**Potassium sulfate contains 16% S
***Potassium magnesium sulfate contains 23% S and 11% magnesium (Mg)

Selecting Fertilizer Type, Timing, and Method of Applications

Phosphate and K2O can be land-applied at any time, but normally it is more cost-effective to apply at the same time as N. However, N is more mobile than P2O5 and K2O in the soil and should be applied as closely as possible to the time of crop uptake. Nitrogen in the form of nitrate can be lost from soils via leaching and can be denitrified to N gas in reducing conditions, such as soils saturated with water.

Ammonium (NH4+) forms of N are subject to losses through volatilization, especially when surface-applied, but because NH4+ has a positive charge, it is retained by soil particles especially when injected below the soil surface. Substantial amounts of ammonium can also be lost from surface applications of urea, especially during the warm summer months; applications of fertilizer salts, such as ammonium sulfate, at these times, will reduce these losses. If leaching and/or denitrification are known to be concerns, then ammonium forms of N can perform better. One of the main causes of soil acidity is the oxidation of ammonium forms of N to nitrate-N, the main plant-available form, but in most situations there is little practical difference between N forms in fertilizers.

Fertilizer applications can be split to improve N-use efficiency by crops. For example, part of the crop N requirement can be applied as starter fertilizer that can be placed in bands beside seed rows when planting row crops. This helps the first stages of crop growth without applying large rates of N that could be lost before the crop requires it. The rest of the crop N requirement can be applied immediately prior to the time of maximum crop uptake. For corn, this means sidedressing with N when it is about 12 inches tall, as this N is applied immediately before the corn has its highest rate of growth and, therefore, its maximum N uptake.

Forages are almost always fertilized by surface broad-casting of granular fertilizers, and they should also be fertilized with N immediately before their maximum periods of growth. For maximum efficiency, this means splitting N applications between spring and late summer/fall for cool season grasses, such as fescue and orchardgrass.

Examples of Calculating Fertilizer Application Rates

In order to calculate a fertilizer application rate, you will need: (1) the N-P2O5-K2O content of the material from the package label, (2) your target rate (normally from a soil test), (3) the total area you will be applying to, and (4) the density of the material if a liquid fertilizer is to be used.

Example 1: Liquid nitrogen fertilizer for corn
A liquid N fertilizer (30% UAN) is the N source for 500 acres of corn. Calculate the N application rate in gallons per acre and the total tons of fertilizer needed to apply 160 pounds of N per acre to the 500 acres. The fertilizer weighs 10.86 pounds per gallon and contains 30% N by weight. The 30% UAN has 30% N by weight, which means 0.30 pound of N per pound of fertilizer.

Calculation:

Lb N/gal of fertilizer solution = 10.86 lb/gal x 0.30 lb N/lb of fertilizer = 3.26 lb N/gal.

Gal of UAN/acre = 160 lb N/acre ÷ 3.26 lb N/gal = 49.1 gal/acre.

Tons for 500 acres = (49.1 gal/acre x 500 acres x 10.86 lb/gal) ÷ 2000 lb/ton = 133.3 tons.

Example 2: Dry fertilizer for turf application
An 18-0-18 + 3% iron (Fe) fertilizer must be applied to supply 1.0 pound of N per 1,000 square feet of turf. Calculate the rate of fertilizer to apply to obtain the proper N rate and also calculate the amount of Fe that is applied at the rate of application used to supply the needed nitrogen. There is 18% N in 18-0-18 fertilizer = 0.18 pound of N per pound of fertilizer.

Calculation:

Rate of fertilizer to apply 1 lb N/1,000 sq ft = 1.0 lb N ÷ 0.18 lb N/lb of fertilizer = 5.56 lb 18-0-18 + 3% Fe/1,000 sq ft.

Amount of Fe applied = (5.56 lb fertilizer/1,000 sq ft) x 0.03 = 0.17 lb Fe/1,000 sq ft.

Example 3: Dry fertilizer application to forage
Granular ammonium sulfate (21-0-0-24S) is being used to supply N for stockpiled fescue. Calculate the amount of fertilizer that must be applied per acre to supply 60 pound N per acre.

Calculation:

60 lb N/acre ÷ 0.21 = 286 lb ammonium sulfate/acre.


Virginia Cooperative Extension materials are available for public use, reprint, or citation without further permission, provided the use includes credit to the author and to Virginia Cooperative Extension, Virginia Tech, and Virginia State University.

Virginia Cooperative Extension is a partnership of Virginia Tech, Virginia State University, the U.S. Department of Agriculture, and local governments. Its programs and employment are open to all, regardless of age, color, disability, sex (including pregnancy), gender, gender identity, gender expression, genetic information, ethnicity or national origin, political affiliation, race, religion, sexual orientation, or military status, or any other basis protected by law.

Publication Date

August 6, 2024